• Portal
  • Forum
  • Search
  • Member
  • Misc
    • View New Posts
    • View Today's Posts
    • Permission
    • Help Docs
Login or Register Hello There, Guest! Please Login or Register to gain Full Access!
Login
Username/Email:
Password: Lost Password?
 

  1. Metal Detector Forums for The Hobbyist
  2. Metal Detecting
  3. Detector Questions
  4. Pinpointer :: Minelab Pro-Find 35 Operating Instructions
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Thread Modes
Pinpointer :: Minelab Pro-Find 35 Operating Instructions
MDH
Administrator
*******
Posts: 2
Threads: 2
Joined: Oct 2018
Reputation: 0
#1
11-03-2018, 06:01 PM
Operating Instructions 

Power On 
With probe at least 300mm/1' away from metal objects, press the Power button. The unit will beep twice and the LED (3)* will illuminate. When auto-calibration is complete, a short beep indicates that the pinpointer is ready to use. When a detection occurs, the vibration will intensify, and the beeps will emit increasingly closer together. When the detected object is very close to the probe, the beep becomes a continuous tone. 

Power Off 
Press the Power button. Three short beeps will emit and the pinpointer will power off. Lost-Alarm When the pinpointer is switched on but has been inactive for approximately 3 minutes, a long alert beep will emit. This will repeat every 10 seconds unless a detection occurs. If the pinpointer is inactive for another 5 minutes, it will automatically power off. Low Battery Low Battery is indicated by a flashing LED. When the battery level is critically low, the pinpointer will automatically power off.

Lost-Alarm
When the pinpointer is switched on but has been inactive for approximately 3 minutes, a long alert beep will emit. This will repeat every 10 seconds unless a detection occurs. If the pinpointer is inactive for another 5 minutes, it will automatically power off. 

Low Battery
Low Battery is indicated by a flashing LED. When the battery level is critically low, the pinpointer will automatically power off. 

Sensitivity
To increase sensitivity, press +. When maximum sensitivity is exceeded (level 5), there will be a long beep. To decrease sensitivity, press – . When minimum sensitivity is exceeded (level 1), there will be a long beep.

Ferrous Tone ID

To enable Ferrous Tone ID, hold the pinpointer away from metal objects, then press and hold + (6) for 3 seconds. There will one long beep. When the pinpointer is close to the target: Interrupted chirping tones upon detection indicate a ferrous target. Ferrous Tone ID is effective when the probe is 10–15 mm (approx. ½") from a ferrous object. 

To disable Ferrous Tone ID, press and hold –  for 3 seconds, until the unit emits one long beep.

Audio Indication
To turn audio tones ON (default), hold down + when turning on the pinpointer. To turn audio tones OFF, hold down – when turning on the pinpointer. If + or – are not pressed at all when turning on the pinpointer, it will default to the last-use audio mode.

Factory Reset
From off, press and hold the Power button (5). After two long beeps, continue to hold for 5 seconds. One long beep followed by two short beeps will indicate when Factory Reset is complete. 

General Maintenance
To maintain a waterproof/splash proof seal, ensure that the battery cap O-ring is periodically lubricated with silicone grease. Always check that the battery cap O-ring and screw threads are clear of dust, sand, and grit.
Find
Reply
« Next Oldest | Next Newest »


  • View a Printable Version
  • Subscribe to this thread
Forum Jump:


Users browsing this thread: 1 Guest(s)

About Our Community

Discuss about various topics in our community and have fun while doing so. Welcome to Metal Detector Forums for The Hobbyist

Quick Links



Reach Us

Contact Us  Meet Our team

Copyright © 2019 - www.MetalDetectorHobbyist.com - White Marsh, Maryland - All rights reserved.
Linear Mode
Threaded Mode